
In this article
Australia banned the manufacture, supply, processing and installation of engineered stone benchtops, panels and slabs from 1 July 2024. You can keep an existing benchtop in place. If you’re renovating or need to repair or remove one, here’s what the ban covers and what products you can choose instead.
Each state and territory enforces the ban under its own work health and safety laws. Check with your regulator for the conditions that apply to your job.
Why was engineered stone banned?
Safe Work Australia says the ban was based on its recommendation in response to rising cases of silicosis, particularly in engineered stone workers. The danger is the dust. Cutting, grinding and polishing engineered stone can release respirable crystalline silica, which workers can breathe in.
WHS ministers agreed to the ban on 13 December 2023, and the Commonwealth and all states and territories put it in place from 1 July 2024.
What exactly is banned?
The ban generally makes it unlawful for a business to manufacture, supply, process or install engineered stone benchtops, panels or slabs, or direct or allow a worker to do that work. Limited exceptions apply, including for some work on existing installations.
For the ban, engineered stone is defined as an artificial product that:
contains at least 1% crystalline silica (by weight)
is made by combining natural stone materials with other chemical constituents such as water, resins or pigments, and
becomes hardened.
A product must meet all three parts of the definition, and be a benchtop, panel or slab, to be banned. From 1 January 2025, engineered stone benchtops, panels and slabs also became prohibited imports.
There was no transition period in Victoria or Queensland. WorkSafe Victoria and WorkSafe Queensland both say the ban applies even if a contract was signed before 1 July 2024.
What isn't covered by the ban?
Safe Work Australia lists these products as not engineered stone under the rules:
concrete and cement products
bricks, pavers and similar blocks
ceramic wall and floor tiles
sintered stone, as long as it doesn't contain resin
porcelain products, as long as they don't contain resin
roof tiles
grout, mortar and render
plasterboard.
Safe Work Australia also gives examples of products that aren't prohibited:
an artificial stone benchtop, panel or slab with less than 1% crystalline silica
a porcelain or sintered stone benchtop, panel or slab that doesn't contain resin
finished products such as engineered stone sinks and ornaments that are ready to use and need no further processing, and are not benchtops, panels or slabs.
Can I keep my existing engineered stone benchtop?
Yes. WorkSafe Queensland says an existing benchtop can stay in place. The health risk comes from breathing in dust when the material is disturbed, for example by cutting, drilling or polishing.
The risk comes back if dust is created during removal, repairs, modifications or disposal.
Can an engineered stone benchtop be repaired or removed?
Yes, within limits. Benchtops, panels and slabs already installed are called "legacy" engineered stone. Businesses can still:
remove, repair or make minor modifications to installed engineered stone
dispose of engineered stone, whether it's installed or not.
Before starting, the business needs to check its local regulator’s notification rules. Under the model rules a current notification can cover work for 12 months, so a fresh notice is generally unnecessary for each job. Victoria doesn’t require notification for permitted legacy work. Wherever the work takes place, any processing must be controlled, with measures to suppress or capture dust and suitable respiratory protection.
If you’re a homeowner, arrange for a tradesperson experienced in legacy engineered stone to do the work. Ask how they’ll control dust and meet the rules for your state or territory.
Can a benchtop be taken out and put back in?
Reinstalling an existing benchtop is generally covered by the installation ban. Safe Work Australia says all jurisdictions have granted exemptions for certain jobs. Check the conditions in your state or territory before removing a benchtop you plan to reinstall.
In NSW, the exemption covers temporary removal to work on cabinetry, a supporting structure or an underlying component. The original benchtop, panel or slab must go back in the same place at the same address. Only minor modifications or repairs are allowed. The business must notify SafeWork NSW and use controlled processing. If the original can’t be reinstalled, choose a material outside the ban.
Rules vary by state, so ask your tradie to confirm what applies where you live.
What if my building contract includes engineered stone?
In Victoria, WorkSafe Victoria says owners and builders must vary existing contracts so an alternative product is installed. Consumer Affairs Victoria notes a variation may increase or decrease the cost of your build and may cause delays while the builder sources the new product. If you can't agree, contact your state's consumer or building regulator for help with the dispute.
What can I use instead of engineered stone?
The ban covers one specific group of products. Common benchtop materials outside it include:
Natural stone, such as granite or marble. These aren't artificial products, so they fall outside the engineered stone definition.
Porcelain and sintered stone, as long as they don't contain resin.
Low-silica artificial stone, but only if it genuinely contains less than 1% crystalline silica.
Laminate, timber, stainless steel and concrete. Concrete and cement products are specifically excluded. Other materials such as laminate, timber and stainless steel aren't stone products, so they aren't covered by the definition.
There are two catches.
Check claims such as “low silica” with your supplier. Ask for the safety data sheet and check the crystalline silica content and composition against the legal definition. If the sheet leaves this unclear, ask the supplier for written product information before you order or cut it.
Processing other stone can also create harmful dust. The model WHS rules strengthened controls from 1 September 2024 for work with materials containing at least 1% crystalline silica by weight. Whether you’re working with natural stone, porcelain or sintered stone, check the product information and follow your local regulator’s requirements for dust control.
What does the ban mean for tradies?
If you fabricate, install or renovate kitchens and bathrooms:
don't supply or install engineered stone benchtops, panels or slabs
check local notification requirements before removing, repairing, modifying, reinstalling or disposing of legacy engineered stone
use controlled processing for any permitted work
check the safety data sheet for any "stone-look" product before you cut it
check whether your state's reinstallation exemption covers the job.
Find a business for your renovation
Planning a new benchtop? You can browse building and renovation businesses, carpenters and cabinetmakers and building materials suppliers on TradeBench.
This article is general information only. WHS rules and exemptions can change and may differ between states and territories, so check with your WHS regulator before starting work.
FAQs
Is engineered stone banned in Australia?
Yes. Since 1 July 2024, the manufacture, supply, processing and installation of engineered stone benchtops, panels and slabs has been banned in every state and territory.
Is my existing engineered stone benchtop dangerous?
Safe Work Australia says available evidence suggests it doesn't pose a safety risk once installed, as long as it isn't cut, polished or otherwise processed.
Are porcelain and sintered stone benchtops banned?
No, provided they don't contain resin. They're excluded from the definition of engineered stone, but they should still be cut with proper dust controls.
Can I cut or remove my engineered stone benchtop myself?
Arrange for a tradesperson experienced in legacy engineered stone to do the work. Ask what dust controls and respiratory protection they’ll use.
Can I buy a new engineered stone benchtop if I signed a contract before the ban?
No. Transitional arrangements for contracts signed before the ban have ended. If your contract still specifies a banned benchtop, speak with your builder about agreeing on another material.